1
/** @name Buffer Descriptor offsets
2
* USR fields are defined by higher level IP. For example, checksum offload
3
* setup for EMAC type devices. The 1st 8 words are utilized by hardware. Any
4
* words after the 8th are for software use only.
7
#define DMA_BD_BUFL_STATUS_OFFSET 0x00 /**< Buffer length + status */
8
#define DMA_BD_USRL_OFFSET 0x04 /**< User logic specific - LSBytes */
9
#define DMA_BD_USRH_OFFSET 0x08 /**< User logic specific - MSBytes */
10
#define DMA_BD_CARDA_OFFSET 0x0C /**< Card address */
11
#define DMA_BD_BUFL_CTRL_OFFSET 0x10 /**< Buffer length + control */
12
#define DMA_BD_BUFAL_OFFSET 0x14 /**< Buffer address LSBytes */
13
#define DMA_BD_BUFAH_OFFSET 0x18 /**< Buffer address MSBytes */
14
#define DMA_BD_NDESC_OFFSET 0x1C /**< Next descriptor pointer */
16
/* Bit masks for some BD fields */
17
#define DMA_BD_BUFL_MASK 0x000FFFFF /**< Byte count */
18
#define DMA_BD_STATUS_MASK 0xFF000000 /**< Status Flags */
19
#define DMA_BD_CTRL_MASK 0xFF000000 /**< Control Flags */
21
/* Bit masks for BD control field */
22
#define DMA_BD_INT_ERROR_MASK 0x02000000 /**< Intr on error */
23
#define DMA_BD_INT_COMP_MASK 0x01000000 /**< Intr on BD completion */
25
/* Bit masks for BD status field */
26
#define DMA_BD_SOP_MASK 0x80000000 /**< Start of packet */
27
#define DMA_BD_EOP_MASK 0x40000000 /**< End of packet */
28
#define DMA_BD_ERROR_MASK 0x10000000 /**< BD had error */
29
#define DMA_BD_USER_HIGH_ZERO_MASK 0x08000000 /**< User High Status zero */
30
#define DMA_BD_USER_LOW_ZERO_MASK 0x04000000 /**< User Low Status zero */
31
#define DMA_BD_SHORT_MASK 0x02000000 /**< BD not fully used */
32
#define DMA_BD_COMP_MASK 0x01000000 /**< BD completed */
36
#define DMA_BD_MINIMUM_ALIGNMENT 0x40 /**< Minimum byte alignment */
38
/* Common DMA registers */
39
#define REG_DMA_CTRL_STATUS 0x4000 /**< DMA Common Ctrl & Status */
41
/* These engine registers are applicable to both S2C and C2S channels.
42
* Register field mask and shift definitions are later in this file.
45
#define REG_DMA_ENG_CAP 0x00000000 /**< DMA Engine Capabilities */
46
#define REG_DMA_ENG_CTRL_STATUS 0x00000004 /**< DMA Engine Control */
47
#define REG_DMA_ENG_NEXT_BD 0x00000008 /**< HW Next desc pointer */
48
#define REG_SW_NEXT_BD 0x0000000C /**< SW Next desc pointer */
49
#define REG_DMA_ENG_LAST_BD 0x00000010 /**< HW Last completed pointer */
50
#define REG_DMA_ENG_ACTIVE_TIME 0x00000014 /**< DMA Engine Active Time */
51
#define REG_DMA_ENG_WAIT_TIME 0x00000018 /**< DMA Engine Wait Time */
52
#define REG_DMA_ENG_COMP_BYTES 0x0000001C /**< DMA Engine Completed Bytes */
54
/* Register masks. The following constants define bit locations of various
55
* control bits in the registers. For further information on the meaning of
56
* the various bit masks, refer to the hardware spec.
58
* Masks have been written assuming HW bits 0-31 correspond to SW bits 0-31
61
/** @name Bitmasks of REG_DMA_CTRL_STATUS register.
64
#define DMA_INT_ENABLE 0x00000001 /**< Enable global interrupts */
65
#define DMA_INT_DISABLE 0x00000000 /**< Disable interrupts */
66
#define DMA_INT_ACTIVE_MASK 0x00000002 /**< Interrupt active? */
67
#define DMA_INT_PENDING_MASK 0x00000004 /**< Engine interrupt pending */
68
#define DMA_INT_MSI_MODE 0x00000008 /**< MSI or Legacy mode? */
69
#define DMA_USER_INT_ENABLE 0x00000010 /**< Enable user interrupts */
70
#define DMA_USER_INT_ACTIVE_MASK 0x00000020 /**< Int - user interrupt */
71
#define DMA_USER_INT_ACK 0x00000020 /**< Acknowledge */
72
#define DMA_MPS_USED 0x00000700 /**< MPS Used */
73
#define DMA_MRRS_USED 0x00007000 /**< MRRS Used */
74
#define DMA_S2C_ENG_INT_VAL 0x00FF0000 /**< IRQ value of 1st 8 S2Cs */
75
#define DMA_C2S_ENG_INT_VAL 0xFF000000 /**< IRQ value of 1st 8 C2Ss */
77
/** @name Bitmasks of REG_DMA_ENG_CAP register.
80
/* DMA engine characteristics */
81
#define DMA_ENG_PRESENT_MASK 0x00000001 /**< DMA engine present? */
82
#define DMA_ENG_DIRECTION_MASK 0x00000002 /**< DMA engine direction */
83
#define DMA_ENG_C2S 0x00000002 /**< DMA engine - C2S */
84
#define DMA_ENG_S2C 0x00000000 /**< DMA engine - S2C */
85
#define DMA_ENG_TYPE_MASK 0x00000030 /**< DMA engine type */
86
#define DMA_ENG_BLOCK 0x00000000 /**< DMA engine - Block type */
87
#define DMA_ENG_PACKET 0x00000010 /**< DMA engine - Packet type */
88
#define DMA_ENG_NUMBER 0x0000FF00 /**< DMA engine number */
89
#define DMA_ENG_BD_MAX_BC 0x3F000000 /**< DMA engine max buffer size */
92
/* Shift constants for selected masks */
93
#define DMA_ENG_NUMBER_SHIFT 8
94
#define DMA_ENG_BD_MAX_BC_SHIFT 24
96
/** @name Bitmasks of REG_DMA_ENG_CTRL_STATUS register.
99
/* Interrupt activity and acknowledgement bits */
100
#define DMA_ENG_INT_ENABLE 0x00000001 /**< Enable interrupts */
101
#define DMA_ENG_INT_DISABLE 0x00000000 /**< Disable interrupts */
102
#define DMA_ENG_INT_ACTIVE_MASK 0x00000002 /**< Interrupt active? */
103
#define DMA_ENG_INT_ACK 0x00000002 /**< Interrupt ack */
104
#define DMA_ENG_INT_BDCOMP 0x00000004 /**< Int - BD completion */
105
#define DMA_ENG_INT_BDCOMP_ACK 0x00000004 /**< Acknowledge */
106
#define DMA_ENG_INT_ALERR 0x00000008 /**< Int - BD align error */
107
#define DMA_ENG_INT_ALERR_ACK 0x00000008 /**< Acknowledge */
108
#define DMA_ENG_INT_FETERR 0x00000010 /**< Int - BD fetch error */
109
#define DMA_ENG_INT_FETERR_ACK 0x00000010 /**< Acknowledge */
110
#define DMA_ENG_INT_ABORTERR 0x00000020 /**< Int - DMA abort error */
111
#define DMA_ENG_INT_ABORTERR_ACK 0x00000020 /**< Acknowledge */
112
#define DMA_ENG_INT_CHAINEND 0x00000080 /**< Int - BD chain ended */
113
#define DMA_ENG_INT_CHAINEND_ACK 0x00000080 /**< Acknowledge */
115
/* DMA engine control */
116
#define DMA_ENG_ENABLE_MASK 0x00000100 /**< DMA enabled? */
117
#define DMA_ENG_ENABLE 0x00000100 /**< Enable DMA */
118
#define DMA_ENG_DISABLE 0x00000000 /**< Disable DMA */
119
#define DMA_ENG_STATE_MASK 0x00000C00 /**< Current DMA state? */
120
#define DMA_ENG_RUNNING 0x00000400 /**< DMA running */
121
#define DMA_ENG_IDLE 0x00000000 /**< DMA idle */
122
#define DMA_ENG_WAITING 0x00000800 /**< DMA waiting */
123
#define DMA_ENG_STATE_WAITED 0x00001000 /**< DMA waited earlier */
124
#define DMA_ENG_WAITED_ACK 0x00001000 /**< Acknowledge */
125
#define DMA_ENG_USER_RESET 0x00004000 /**< Reset only user logic */
126
#define DMA_ENG_RESET 0x00008000 /**< Reset DMA engine + user */
128
#define DMA_ENG_ALLINT_MASK 0x000000BE /**< To get only int events */
130
#define DMA_ENGINE_PER_SIZE 0x100 /**< Separation between engine regs */
131
#define DMA_OFFSET 0 /**< Starting register offset */
132
/**< Size of DMA engine reg space */
133
#define DMA_SIZE (MAX_DMA_ENGINES * DMA_ENGINE_PER_SIZE)
136
#define TX_CONFIG_ADDRESS 0x9108 /* Reg for controlling TX data */
137
#define RX_CONFIG_ADDRESS 0x9100 /* Reg for controlling RX pkt generator */
138
#define PKT_SIZE_ADDRESS 0x9104 /* Reg for programming packet size */
139
#define STATUS_ADDRESS 0x910C /* Reg for checking TX pkt checker status */
141
/* Test start / stop conditions */
142
#define PKTCHKR 0x00000001 /* Enable TX packet checker */
143
#define PKTGENR 0x00000001 /* Enable RX packet generator */
144
#define CHKR_MISMATCH 0x00000001 /* TX checker reported data mismatch */
145
#define LOOPBACK 0x00000002 /* Enable TX data loopback onto RX */